mirror of
https://github.com/foxlet/macOS-Simple-KVM.git
synced 2024-11-27 05:29:42 +01:00
527588d5a2
It's also possible to let QEMU control your tun/tap devices. It's only needed to create a bridge device with f.e. netctl.
91 lines
2.8 KiB
Markdown
91 lines
2.8 KiB
Markdown
Guide to Bridged Networking
|
|
===========================
|
|
|
|
*Note*: you don't need to set up bridged networking just to get internet access. With `basic.sh` you should be able to access the internet from MacOS automatically. *However*, the ICMP protocol (used for `ping`) is not supported with the default networking solution.
|
|
|
|
To set up bridged networking for the macOS VM, use one of the following methods:
|
|
|
|
|
|
## Using /etc/network/interfaces
|
|
|
|
It is possible to create the bridge and tun/tap interfaces by adding the following lines to `/etc/network/interfaces`. Replace `DEVICENAME` with your ethernet card's device name, and `MYUSERNAME` with the user that is starting the VM.
|
|
|
|
```
|
|
auto br0
|
|
iface br0 inet dhcp
|
|
bridge_ports DEVICENAME tap0
|
|
|
|
auto tap0
|
|
iface tap0 inet dhcp
|
|
pre-up tunctl -u MYUSERNAME -t tap0
|
|
```
|
|
|
|
## Using NetworkManager
|
|
You can use NetworkManager to control the bridge and tun/tap interfaces, by creating them with the following commands. Replace `DEVICENAME` with your ethernet card's device name.
|
|
|
|
### Make the Bridge
|
|
```
|
|
nmcli connection add type bridge \
|
|
ifname br1 con-name mybridge
|
|
```
|
|
|
|
### Attach Bridge to Ethernet
|
|
```
|
|
nmcli connection add type bridge-slave \
|
|
ifname DEVICENAME con-name mynetwork master br1
|
|
```
|
|
|
|
### Make the Tun/Tap
|
|
```
|
|
nmcli connection add type tun \
|
|
ifname tap0 con-name mytap \
|
|
mode tap owner `id -u`
|
|
```
|
|
|
|
### Attach Tun/Tap to Bridge
|
|
```
|
|
nmcli connection mod mytap connection.slave-type bridge \
|
|
connection.master br1
|
|
```
|
|
|
|
## Attach Bridge to QEMU
|
|
Once you have set up the bridge and tun/tap on the host, you'll have to add the following line to `basic.sh`, replacing `-netdev user,id=net0`. Change `tap0` to your corresponding device name.
|
|
|
|
```
|
|
-netdev tap,id=net0,ifname=tap0,script=no,downscript=no \
|
|
```
|
|
You can optionally use the `vmxnet3` driver for higher performance compared to the default e1000. Note that replacing it requires macOS El Capitan or higher.
|
|
```
|
|
-device vmxnet3,netdev=net0,id=net0,mac=52:54:00:c9:18:27 \
|
|
```
|
|
|
|
## Using Netctl
|
|
You can also use netctl and the qemu bridge helper to control the bridge and tun/tap interfaces. Replace `DEVICENAME` with your ethernet card's device name.
|
|
|
|
### Create netctl configuration file in /etc/netctl (f.e. /etc/netctl/kvm-bridge)
|
|
```
|
|
Description="Bridge Interface br10 : DEVICENAME"
|
|
Interface=br10
|
|
Connection=bridge
|
|
BindsToInterfaces=(DEVICENAME)
|
|
IP=dhcp
|
|
# If you want also for DHCPv6,uncomment below line
|
|
#IP6=dhcp
|
|
```
|
|
|
|
### Activate netctl bridge handler with system boot
|
|
```
|
|
sudo netctl enable kvm-bridge
|
|
```
|
|
|
|
### Create bridge whitelist file for qemu (/etc/qemu/bridge.conf)
|
|
```
|
|
allow br10
|
|
```
|
|
|
|
## Attach Bridge to QEMU
|
|
Now you'll have to add the following line to `basic.sh`, replacing `-netdev user,id=net0`. Change `br10` to your corresponding device name.
|
|
|
|
```
|
|
-netdev bridge,br=br10,id=net0 \
|
|
```
|