mujmap is a tool that synchronizes mail between a mail server and
notmuch via JMAP. It's very similar to lieer, so I heavily based the
implementation of the notmuch module on lieer's. I did not include an
equivalent to lieer's periodic synchronization service, however,
because I plan to soon introduce a daemon mode to mujmap.
https://github.com/elizagamedev/mujmap
Add services.emacs.startWithUserSession boolean to indicate that Emacs
must be started with the systemd user session. This is true by default
unless socket activation is also true.
In the past, the user had to choose between socket activation (to get
the Emacs service started when the user uses emacsclient) and
immediate start with the user session. When choosing immediate start
over socket activation and if the Emacs service is stopped at some
point, using emacsclient would start a new Emacs daemon but the
service would still be turned off. This situation would prevent
`home-manager switch` from completing successfully because it wouldn't
be able to start the Emacs service as Emacs is already running.
This new setting makes it possible to have both socket activation and
immediate start at the same time. In this scenario, Emacs is started
with the user session and, after the Emacs service is stopped, using
emacsclient starts the service again.
This new settings also makes it possible to have neither socket
activation nor immediate start.
M_SHARE is not a valid column on Darwin. It seems that previously htop
ignored unknown columns, but the current version does not display all
subsequent columns.
This is adapted from the `services.mopidy` NixOS module. The
difference is the setting can be configured with Nix language, taking
advantage of generators from nixpkgs. The module is also suited more
for user-specific configuration, removing the `extraConfigFiles` and
`dataDir` option.
This module adds basic support for configuration specializations.
These allow the user to build multiple alternative configurations that
should be part of the same generation.
Neomutt will run the given command (which can be a string or a path)
and take the output from stdout and use it as the signature for your
email.
Co-authored-by: Nicolas Berbiche <nicolas@normie.dev>
Removed by upstream since commit:
bcbc410c92
This commit is included since v9 release:
https://github.com/yshui/picom/releases/tag/v9https://github.com/yshui/picom/releases/tag/v9-rc1 (the actual changelog)
While this doesn't break the config per see, it results in the
following warning in the logs:
[ DD/MM/YYYY HH:MM:SS.mmm parse_config_libconfig WARN ] The
refresh-rate option has been deprecated. Please remove it from
your configuration file. If you encounter any problems without
this feature, please feel free to open a bug report
Beside the above change we also remove an old workaround and also
write the configuration file to a well-known location in the user's
home directory.
This is achieved by generating the Home Manager configuration
file as `~/.config/task/home-manager-taskrc`, and including that
file into ~/.config/task/taskrc.
Fixes#2360
Co-authored-by: mainrs <5113257+mainrs@users.noreply.github.com>
Co-authored-by: Nicolas Berbiche <nicolas@normie.dev>
* systemd: fix creation of user service unit files
* helix: fix failing test due to file output format change
Co-authored-by: Nicolas Berbiche <nicolas@normie.dev>
The conversion from `concatMapStrings` to `concatStringsSep` introduced in https://github.com/nix-community/home-manager/pull/2481
creates an unintended behavior change where the formatted config does not end in a newline.[1]
This is problematic for manipulation at the Nix level. In particular, this cause a regression in
the generation of gtk2 settings due to concatenated of the formatted config and `gtk2.extraConfig`
without a newline in between.
This commit restores `concatMapStrings` to match the previous behavior and adds a newline to
the final string for the generated gtk2 config. The test case for gtk2-basic-config
was also updated to check behavior at concatenation boundaries.
[1] - https://github.com/nix-community/home-manager/pull/2481#discussion_r830648706
If set to true, desktops configured in `monitors` will be reset every time
the config is run.
If set to false, desktops will only be configured the first time the config is run.
This is useful if you want to dynamically add desktops and you don't want them
to be destroyed if you re-run `bspwmrc`.
Nix permits user level configurations through ~/.config/nix/nix.conf that allow
customization of system-wide settings and behavior. This is beneficial in chroot
environments and for per-user configurations. System level Nix configurations in the
form of /etc/nix/nix.conf can be specified declaratively via the NixOS nix module but as
of currently no counter part exists in home-manager.
This PR is a port of the RFC42 implementation for the NixOS nix module[1]
to home-manager. Non-applicable options have been excluded and the config generation
backends have been tweaked to the backends offered by home-manager. A notable change
from the NixOS module is a mandatory option to specify the Nix binary corresponding
to the version "nix.conf" should be generated against. This is necessary because
the validation phase is dependent on the `nix show-config` subcommand on the host platform.
While it is possible to avoid validation entirely, the lack of type checking was deemed too significant.
In NixOs, the version information can be retrieved from the `package` option itself which
declares the Nix binary system-wide. However in home-manager, there is no pure way to
detect the system Nix version and what state version the "nix.conf" should be generated
against. Thus an option is used to overcome this limitation by forcing the user to
specify the Nix package. Note this interaction can still be automated by forwarding
the system-wide Nix package to the home-manager module if needed.
Three unit tests were added to test the module behavior for the empty settings, the example
settings and the example registry configurations respectively.
[1] - NixOS/nixpkgs#139075
* gtk: add cursor theme configuration
- Added the `cursorTheme` under the gtk module.
- Added tests for the gtk3 settings file generation, and renamed
the gtk2 unit test expected file for clarity.
- Added guard against generating a blank `gtk.css` when `cfg.extraCss`
is empty.
- Replaced `concatMapStrings` calls with `concatStringsSep`. The library function
`concatMapStrings` generates an intemediate list which is then passed to
`concatStringsSep`, As we are not performing other transformation except
the addition of newlines, a direct call to `concatStringsSep` is sufficient.
- Updated description of examples to be more general "~/.config" -> "$XDG_CONFIG_HOME".
- Update helper functions `toGtk3Ini` and `formatGtk2Option` to use the library
function `boolToString` and escape the separator in the key name.
* xcursor: delegate GTK cursor settings to gtk.cursorTheme
- Added deprecation warning for GTK settings in the `xsession.cursorTheme` module.
- Modified config section to use `gtk.cursorTheme` for GTK cursor settings.
This has no effect if the user does not have any aliases defined for
any accounts.
This will also only add `--my-address=` to only accounts that are
enabled to be tracked by mu.
Note, the pubs configuration file uses ConfigObj syntax, which is
similar to the INI files syntax but with extra functionalities like
nested sections. This prevents it from using Nix's INI format
generator. Here is an example of pubs configuration that cannot be
generated using Nix's INI format generator:
[plugins]
[[git]]
manual=False
For this reason, we opted for a stringly-typed configuration since the
use of a structured `settings` option would require a custom parser.
